Відео

Them cheap circuit breakers are junk. They do not provide adequate protection. Need to buy a brand name one.

Soak them with water before cutting. Less dust, cooler blade, better, faster, safer.

Only problem with all these ice a/c is You gotta consider the Cost of ICE if you on a let say small cabin Boat Cdory or such for a few weeks you gonna burn at least 3 bags of ice a day MIN Ice isnt Cheap especially at Marinas and such u looking at 10 bucks a day just for Ice, Min. gotta weight out all the options.

I also bought 50ah Eco Worthy, after full charge it almost immediately drops to 13,36 V. In comparison with my other lifepo4 batteries (selfmade from single cells) which hold stable 13,6 V. I am a bit disappointed with Eco Worthy.

This inflatable isn't made to take a full heavy outboard.

Welding is danger

U have the the cheap one and I can say I thought it was normal but I can not see the puddle so I’m going with the middle one tomorrow

I would personally use 1" felt on the inside of the cover. I use to soundproof 1400 amp Motion Picture generators that would operate at a sound level of 50 decibels at 50 feet. People can get more extreme as we also used soundproof spray on the inside of the housings to further quiet the generators.

Hi man. The first step is overheat the surface to welding?? Thanks..

Seriously, who cares about that, I don't spend any time in my garage and when I do, the door is bloody open, it's a garage not a living room, just shut the door that links the house to the garage, draft exclude that door, its a lot cheaper than doing the garage door, looks like this guy is trying to sell something no one needs

Great video !

If u want really kill sound u need dense product everyone agrees Sheetrock is great for this also have a box then a second box with some spacers strips giving 1 1/2” 2” gap between 2

Have you ever installed patio pavers? What was your first step?

Purchased this from Amazon last week. Works great….

What do you guys think about this technique? Is the terry cloth enough to protect the saw?

Love the saw cover!

Do it Fred, DO IT!!!

If I did I would keep the carpet in one piece and make it so it folds right sides together

Bonjour Quel épaisseur la planche du fond ?

Hello was hoping you could answer a couple questions I have about the seahawk build

Yeah the floor makes a huge difference especially when you bring your dog on board I found you don’t even need the noodles it’s just the floor tucks right into the inner chamber and it’s not going anywhere

I got the first one with the blue flames worst decision ever

Hi Fred ! Thanks for your video. Do you know about the consumption in watts/h of your electric boat engine ? I have the same intex boat with a Rhino vx 54lbs . In the specs, its written 360watts/hr at the 5th gear which is the max. Also, how was the difference with the wooden support you have put ? Did you notice any change ? Thanks again for the cool video :) greetings from France.

I've been on the fence about getting this trailer thank you for all the videos. I will be waiting for the tire video. Mahaloz!

Looks like the middle one was the best view / clarity

Excellent video…thanks

Great video! I can't wait to get myself one of these trailers, although I've heard there's supply issues right now. I have also read in forums that some people have trouble with frame twisting over time when mounting trailer jacks on the side of the tongue, some people even said they had up to 6" dips over several years. I've seen people make brackets to mount it centered in the A frame behind the tongue and that's probly the route that I will go.

I would love to see how these performed in a little cooler temps.

The weld might be OK but the heat anneals the surrounding aluminum and the whole thing falls in a heap, so to speak. Most of the strength is gone.

Tell me what you think about my concrete paver project with a comment. How did it turn out? Do you like it?

The most useless test on UA-cam! Thank you!

Hello very good video!! What kind of tape are you using?? Thanks

Why does this feel like one big Advert by an employee or business owner

Thank you, very helpful video. My regulator was leaking and very difficult to turn, almost seized. Inside was completely caked in sludge. Cleaned everything out and lubed up the o-rings and it works great again.

Watch the full video to see what Amazon is NOT TELLING YOU!

I applaud your maturity even if I'm a lil disappointed

only thing he can power up with that setup is his cell phone ....

I am a steel mill electrician, and we deal with an incredible amount of water, oil & grease in the tandem cold mill rolling areas. There are very effective tricks to keep moisture & corrosion out of electrical connections. Wire nuts are fine, with a little extra attention. You need to make sure the exposed wire ends won't corrode & make a bad connection. In a wet area, like underneath a vehicle, coat the wire ends with conductive anti-seize like Penetrox, then twist together and screw a wire nut on them. Tug on each wire to make sure they don't pull out of the nut. Then wrap the nut and a few inches of the insulated wire with electrical tape in the SAME direction you tightened the nut on, to keep it from ever falling off. The few extra inches of wrapped wire acts as a last ditch support if a bracket rots away, leaving the electrical device hanging by the wires. I should point out that both electrical tape and fancy shrink tubing will NEVER keep water out. As added moisture control, you can try to point the wire nuts upward & secure them that way with cable ties, etc., so water can't collect inside of them.

Amazing Game!

Looks awesome, scooped the kit and 4 tanks!

Forget the generator for now...that a nice Trans Am sitting back there

Bought the spacers and ST175/80R 13 tires and rims. Les Schwab Tires would not mount with the spacers, so I had to do it. NO GOOD. The tires run big time against the fender braces. I could barely move it over to my carport. Very disappointing. What else did you do besides installing the spacers?

Good mods but you mine as well purchased a better trailer instead of modifying a cheap one.

Pice of junk. On number 6 now. Never by this JUNK!!

didn't work for my 2018 XLT Thanks though

I just bought one and did change oil after 2 hours and after another 2 hours runn time. I did see alot metal parts in the oil. In the manual it say nothing about changing oil thisbrapid to clean the engen for metal parts. Is this bro sience or super important?

Thanks for the video! I need more research. To be honest, and NOT to troll you (edit) when you did the test with your voice and microphone (first set of tests) I can honestly say the sound WITH the sound panels was LOUDER than before you installed them. I was surprised. When you did the camping test with the running generator, I heard very little difference at all with or without the enclosure. I am very surprised, and would have expected a much larger reduction. Of course/also, your Db meter readout was virtually unreadable on camera, but thanks for showing it anyway! I appreciate your time and will watch more of your videos. Thanks again!

Excellent comparative. Thanks!

Shelve load weight 👍

i do think the single wheel helped the REESE but also the lack of play, maybe the others could be tightened, but from the factory it shouldnt need to be. Also REESE is more of a name brand as you will see them at multiple brick and mortar stores, not just online. , the weight capacity might just be a question of the wheel contact area so only having one wheel would reduce its load capacity, wonder if it could easily be modded to take dual wheels or a bigger/better wheel